Movement during measurement. Carefully read and repeat the steps in section 3. Arm cuff is applied too loosely. Apply the arm cuff tighter. Refer to section 3. The batteries are low. You should replace the batteries with new ones ahead of time.
Refer to section 2. The batteries are exhausted. You should replace the batteries with new ones at once. Page 24 4. Insert the air plug securely. Air is leaking from the arm cuff. Replace the arm cuff with a new one. Refer to section 5. Movement during measurement and the arm cuff has not been inflated sufficiently. EN Repeat measurement. Remain still and do not talk during measurement.
The arm cuff was inflated above mmHg when inflating the arm cuff manually. Do not inflate the arm cuff above mmHg. Repeat measurement. Clothing is interfering with the arm cuff.
Remove any clothing interfering with the arm cuff. Device error. Movement or talking during measurement. The air connector is not securely connected into the air jack. Make sure that the air tube is connected securely. Arm cuff deflates too soon. The arm cuff is loose. Apply the arm cuff correctly so that it is firmly wrapped around the arm.
Cannot measure or the results are too low or too high. The arm cuff has not been inflated sufficiently. Inflate the arm cuff so that it is 30 to 40 mmHg above your previous measurement result. The measurement result is extremely high or low. Arm cuff pressure does not rise.
Replace the batteries with new ones. The batteries have been inserted incorrectly. Nothing happens when you press the buttons.
Other problems. Maintenance and Storage 5. Do not use any abrasive or volatile cleaners. Do not wash the device and any components or immerse them in water. Do not use petrol, thinners or similar solvents to clean the device. Do not disassemble or attempt to repair the device or components. Unplug the air plug from the air jack.
Gently fold the air tube into the EN arm cuff. Note: Do not bend or crease the air tube excessively. Place the monitor and the arm cuff in the storage case. Insert the AC adapter plug into the AC adapter jack on the rear side of the monitor.
Plug the AC adapter into an electrical outlet. To disconnect the AC adapter, unplug the AC adapter from the electrical outlet first and then remove the AC adapter plug from the monitor. Electromagnetic interference may result in incorrect operation of the medical device and create a potentially unsafe situation. Medical devices should also not interfere with other devices. In order to regulate the requirements for EMC Electro Magnetic Compatibility with the aim to prevent unsafe product situations, the EN standard has been implemented.
This standard defines the levels of immunity to electromagnetic interferences as well as maximum levels of electromagnetic emissions for medical devices.
This may result in incorrect operation of the device and create a potentially unsafe situation. Recommendation is to keep a minimum distance of 7 m. Verify correct operation of the device in case the distance is shorter.
Documentation is also available at www. It will with your doctor about what your numbers mean to you. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.
Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Config- urability varies with model. Contents Model Number Structure External connection None: Screw terminals pin socket 2. Stage setting None: 1-stage setting U: Factory-set to 1-stage setting W: Factory-set to 2-stage setting.
Output type None: Contact output or contact and transistor in combination S: Transistor output 5. Y92F Waterproof Packing See note 1. PV Voltage input High logic level: 4. Key protection Yes Prescaling function Yes 0. Input mode: command, individual, or quadrature; output mode: K-2, D, or L. Display See note 2.
Electrical: , operations min. Weight Approx. Increment signals can be input. The reset indicator is lit during reset input. Counting for CP1 input cannot be performed during reset 1 input. The reset indicator is lit during reset 1 input. See note 2. Holds the total count value at 0 during total reset input. Holds the batch count value at 0 during reset 2 input.
Counting for CP2 input cannot be performed during reset 2 input. CP2 input is not available. Reset 1, Reset 2 Holds the measurement value and outputs. Reset 2 input is not available. The reset indicator is lit during hold. Terminals 1 and 6 are connected internally. Contact input Use contact which can adequately switch 5 mA at 10 V.
Maximum applicable voltage: 30 VDC max. Input resistance: Approx. Applicable Two-wire Sensor Leakage current: 1. Switching capacity: 5 mA min. Residual voltage: 3 VDC max. E Batch Indicator Lit when the batch count value is displayed.
J Reset Key The operation of the reset function depends on the configuration selected as shown in the table below. Tachometer Maintains the measured value and outputs hold function. Dimensions Note: All units are in millimeters unless otherwise indicated. Panel Cutouts Panel cutouts are as shown below. Top View holes 4 50 max. Surface Mounting Holes Two, 4. PFPN2 16 4. When Using Advanced Functions Settings for advanced functions other than the basic settings above can be performed with the operation keys.
Setting for Tachometer Operation. OFF When Using Advanced Functions Settings for advanced functions other than the basic settings above can be performed with the operation keys. Be sure to set pin 1 to ON. Advanced-Function Settings After making DIP switch settings for basic operations, advanced functions see note can be added using the operation keys.
Power ON Run mode See note 1. See note 3. Input mode Output mode See note 6. The characters displayed in reverse video are the default settings. Set each setting item using the r r keys.
See note 4. See note 5. D L H Note 6: When using as a 2-stage counter:. Stress raises blood pressure. Avoid taking measurements during stressful times.
The cuff can be applied to your left or right wrist. Measurements should be taken in a quiet place and you should be in a relaxed, seated position. Keep a record of you blood pressure and pulse for you doctor. Remember, a single measurement does not provide an accurate indication of your true blood pressure. You need to take and record several readings over a period of time. Try to measure your blood pressure at the same time each day for consistency. Wait minutes between measurements.
Waiting allows the engorged blood vessels to return to normal. You may require more rest time between readings depending on your individual physiological characteristics. Use this monitor after inserting batteries in the main unit. Place the main unit with the Battery Cover facing upward. Push down the indent portion of Battery Cover and slide it into the direction of the arrow. Insert two AAA Batteries with the polarities. Battery life is shorter under cold conditions such as during the winter.
To avoid pressure on the button when transporting or storing, use the case provided. The monitor stores the measured values and the date and time of measurement, which is helpful for the continuous blood pressure management. However, if more than one person is expected to use this monitor, the measured values of more than one person will be stored. Push the SET button while the power is turned off.
0コメント